Moles and limiting reactants: a stoichiometry method
A balanced equation compares amounts in moles, not masses in grams. Convert each reactant to moles, then divide its amount by its coefficient in the balanced equation. The smallest result identifies the limiting reactant for that reaction. Use it to calculate theoretical product yield. The reactant with the smallest mass is not necessarily limiting, and actual yield may be lower than theoretical yield.
A balanced equation is a recipe measured in particles or moles. Treating its coefficients as gram ratios can produce a neat calculation with the wrong answer.
Keep three quantities separate
| Quantity | Symbol and typical unit | What it tells you |
|---|---|---|
| Mass | m, in g | How much the sample weighs |
| Amount of substance | n, in mol | How many entities the sample contains, on the mole scale |
| Molar mass | M, in g/mol | Mass per mole of that substance |
Use n = m/M. For a solution whose concentration is given in mol/L, use n = cV, with volume in litres. For example, 25 mL of a 0.20 mol/L solution contains 0.0050 mol of solute, not 5 mol.
A coefficient changes the amount of a substance. A subscript changes its chemical identity: 2 H₂O means two water molecules, whereas H₂O₂ is hydrogen peroxide. OpenStax’s stoichiometry chapter develops the conversions between mass and amount using balanced equations.
Worked example: which reactant runs out?
This original example assumes pure reactants and complete conversion through the stated reaction:
2 H₂ + O₂ → 2 H₂O
Start with 6.0 g H₂ and 32.0 g O₂. Use the supplied rounded molar masses: H₂ = 2.0 g/mol, O₂ = 32.0 g/mol, H₂O = 18.0 g/mol.
- Convert to moles: hydrogen = 6.0/2.0 = 3.0 mol; oxygen = 32.0/32.0 = 1.0 mol.
- Divide by coefficients: hydrogen gives 3.0/2 = 1.5; oxygen gives 1.0/1 = 1.0.
- Oxygen gives the smaller value, so oxygen is limiting.
- One mole of oxygen produces two moles of water: theoretical water mass = 2.0 × 18.0 = 36.0 g.
Hydrogen has the smaller initial mass, yet it is in excess. You cannot identify the limiting reactant by comparing grams alone.
Check what is left over
Producing 2.0 mol water consumes 2.0 mol hydrogen. Starting with 3.0 mol leaves 1.0 mol hydrogen, or 2.0 g.
The mass check is reassuring: 38.0 g initially equals 36.0 g water plus 2.0 g leftover hydrogen. Do not expect the product mass alone to equal the total starting mass when some reactant remains unused.
Another useful check: if the calculation requires more oxygen than the 1.0 mol available, it cannot describe this mixture.
Theoretical yield is not the collected yield
Theoretical yield is the maximum predicted from the limiting reactant under the assumed reaction. Actual yield is the amount obtained. Collection losses, incomplete conversion or competing reactions can make it smaller.
Percentage yield = actual yield / theoretical yield × 100%
If the example produces 27.0 g of collected water, the percentage yield is 27.0/36.0 × 100% = 75%. Use the product’s theoretical mass as the denominator, not the combined starting mass. OpenStax explains limiting reactants and yield.
Self-check: a different ratio
For the original practice reaction N₂ + 3 H₂ → 2 NH₃, suppose 0.40 mol N₂ and 0.90 mol H₂ are available. Assume complete conversion by this reaction.
Which reactant limits the yield, and how much ammonia can form?
Compare 0.40/1 with 0.90/3 = 0.30. Hydrogen limits the reaction. It can produce 0.60 mol NH₃ and consumes 0.30 mol N₂, leaving 0.10 mol N₂.
If you chose nitrogen because 0.40 is smaller than 0.90, you compared amounts without allowing for the 1:3 recipe.
Use the same order every time
Balance → convert to moles → compare against coefficients → calculate product → check units and leftovers. When a question supplies only one reactant amount, check whether the other is explicitly in excess before assuming it.
The same bookkeeping comes before pH calculations when acid and base react. Continue with acids, bases and buffers to see why accounting for neutralisation must precede the equilibrium calculation.
Sources
Or keep going in the iPhone app.
Found a mistake? Write to hello@imatlearn.com